Router Charts

Router Charts

Router Ranker

Router Ranker

Router Chooser

Router Chooser

NAS Charts

NAS Charts

NAS Ranker

NAS Ranker

More Tools

More Tools

Wireless Reviews

Introduction

TRENDnet TEW-633GR front view

At a Glance
Product TRENDnet Wireless N Gigabit Router (TEW-633GR)
TRENDnet Wireless N PC Card (TEW-621PC)
Summary Clone of the D-Link DIR-655 with some minor tweaks
Pros • Gigabit WAN and LAN, excellent routing speed & jumbo frame support
• Top-of-chart simultaneous sessions
• WDS Bridging / Repeating
• Top-of-chart wireless performance
Cons • No option to partition wireless traffic
• High throughput variation, especially in 20 MHz mode
• Companion client does not support WPS
• Large difference between up and downlink throughput

As draft 802.11n products gain in popularity, we see attempts to position similar products for different markets. Enter TRENDnet's TEW-633GR Wireless N Gigabit router. Although it's very similar to the D-Link DIR-655 (reviewed here), it's black, which may indicate it was intended for the gaming market. TRENDnet is not consistent in their naming of the router, however, sometimes referring to it as a gaming router, and sometimes not. Not that it matters anyway, since the "gaming" moniker is for marketing purposes only.

The TEW-633GR is essentially a rebadged U-MEDIA WRT-390U. It shares many of the same features and interface characteristics with the DIR-655, so if you're comfortable/familiar with that router, you should find the TEW-633GR easy to use.

Rear view
Click to enlarge image

Figure 1: Rear view, showing connectors

The TEW-633GR measures 6.4" wide x 5.9" long x 1.0" high, and has four LAN ports and one WAN port, as seen in Figure 1. All of the ports are gigabit, which is nice. And nicer still that the LAN switch automatically supports jumbo frames up to 9K, although Trendnet doesn't officially spec this. The rear panel also houses the power connector and a factory defaults reset button.

The little bump on the top of the router in Figure 2 is the WPS button, which enables Wi-Fi Protected Setup. The switch on the side in Figure 2 is used to turn the WLAN radio on or off. Note that this is the only way to enable and disable WLAN functionality. This is both a blessing and a curse. It's a blessing because it's nice to set this option physically, so that it can't be tampered with via the admin interface; it's a curse because it means you have to put the router somewhere accessible if you plan on using the switch often.

Side view
Click to enlarge image

Figure 2: Side view, showing the WLAN on/off switch

More Wireless

Featured Sponsors


Win This!

Linksys Linksys LAPC1750PRO

You could win a Linksys LAPC1750PRO AC1750 Pro Dual-Band Access Point

Learn How!

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Top Performing Routers

AC3200
AC2600
AC1900
AC1750
AC1200

Top Performing NASes

NoRAID
RAID1
RAID5

Over In The Forums

Hi all. I just bought the Linksys 1900ACS. In the last week I have had a wired computer and then my wired Sonos bridge lose internet connection. Th...
Wondering if I SSH in to the router if there's a .config file that I can add an additional DNS server address so that the system will hand out two DNS...
I hope someone can help me. I'm new to VPN and can't seem to get this to work. I created an incoming connection on the windows 10 computer at the off...
Hi All, I was trying out squid with Ausuwrt merline 380.57 firmware but ran into an issue running this command: squid -z I get an error: minhgi@RT...
So I have PIA VPN setup on my router and it works great. I also have it configured to allow some devices through the WAN and not go through the VPN. ...

Don't Miss These

  • 1
  • 2
  • 3