Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Router Charts

Click for Router Charts

Router Ranker

Click for Router Ranker

NAS Charts

Click for NAS Charts

NAS Ranker

Click for NAS Ranker

More Tools

Click for More Tools

NAS How To


The ol' review queue has filled up with products, so the Fast NAS experimentation has moved to the back burner for a bit. But with a little prodding from the Forums crew, I decided to take a quick look to see what sort of performance that iSCSI can bring to the table.

iSCSI is a protocol that allows clients (initiators) to send SCSI commands to SCSI storage devices (targets) via a TCP/IP network connection. iSCSI's main use is to build Storage Area Networks (SAN) using Ethernet-based networks instead of dedicated connections such as Fiber Channel. iSCSI drives appear to an operating system as locally mounted drives.

An opportunity came in the form of the Sans Digital MN4L+B that I spent a much of this week testing. It's based on an Intel Pentium M and its performance runs neck and neck with the QNAP TS 509 Pro that reader Dennis Wood has been having so much fun with.

The MN4L+ (I'll dispense with the "B" since that just indicates the black case version) has both iSCSI initiator and target modes built in along with its high SMB/CIFS performance. So I decided to use the Windows iSCSI initiator to run some iozone tests on the MN4L+ as an iSCSI target.

Windows iSCSI Initiator

I started with Vista, since it has the initiator built right in. But I also ended up downloading and installing the initiator on the copy of XP that is dual-booted on the same machine, which I have been using as the Fast NAS test system. Keep in mind that this system has 512 MB of memory, which causes performance improvement due to caching to fall off sooner.

Figure 1 shows the Windows iSCSI Initiator Properties Control Panel. I didn't mess with changing the Node name, since you must follow a particular convention.

Windows iSCSI Initiator - General

Figure 1: Windows iSCSI Initiator - General

I first made sure that iSCSI target support was enabled on the MN4L+ and that an iSCSI volume was created. I then moved to the Discovery tab (Figure 2) and entered the MN4L+'s IP address. I was a bit puzzled that there was no connection confirmation, so I wondered whether I had actually connected. But I later learned, when I tried to enter an IP address that did not have a valid target, that the Add Target Portal window just stays up and you eventually get an error message in that case.

Windows iSCSI Initiator - Discovery

Figure 2: Windows iSCSI Initiator - Discovery

Clicking on the Advanced button brings up the Advanced Settings window (Figure 3), which contains logon options, including settings for CHAP authentication for secured targets.

Windows iSCSI Initiator - Advanced Settings - General

Figure 3: Windows iSCSI Initiator - Advanced Settings - General

The Advanced Settings - IPsec tab (Figure 4) allows the use of a secure IPsec tunnel secured with a Pre-shared Key for both authentication and data transfer for those targets that support it.

Windows iSCSI Initiator - Advanced Settings - IPsec

Figure 4: Windows iSCSI Initiator - Advanced Settings - IPsec

More NAS

Wi-Fi System Tools
Check out our Wi-Fi System Charts, Ranker and Finder!

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!


Over In The Forums

This is a step-by-step guide that will show how to optimally set up a USB drive for Asus’ RMerlin powered routers that will at the very minimum allow ...
Hi,I last reported this issue about 3 weeks ago over GUI Feedback when one of my AiMesh Node (Bedroom) gone OFFLINE. I rebooted everything and all see...
Download = RT-AX88U Firmware version AiMesh 2.0- S...
I want to replace my Asus RT-N66U router (purchased in 2013) with a brand new model. Please note that this old router seems to work fine - I'm only re...
RT-AC1900P, and brand new windows 10 Home edition. I've turned on Samaba, SMBv1 and SMBv2, as well as guest login but I can't create new folders on th...

Don't Miss These

  • 1
  • 2
  • 3