8 Port Gigabit Switch Roundup

Photo of author

Tim Higgins

Introduction

Six 8 port gigabit switches

As long-time readers of our reviews know, we don’t generally review or test Ethernet adapters and unmanaged switches. The reason for this is that I’m a firm believer that these are commodity products, to be purchased based on price, brand preference and perhaps warranty.

The technology at the heart of these products is well-established and has long-ago been encapsulated into single-chip solutions which offer "wire-speed" performance, i.e. equal to that of a naked cable, both for adapters and switches.

But I have to confess that I had never done any testing to back up my assertion that all switches and NICs (network interface cards) are created equal. That, plus a comment from one reader that he was unable to find a gigabit switch that had performance equal to a straight cable, brings us to this roundup.

We asked the "big three" consumer networking companies—Linksys, Netgear and D-Link—for eight port gigabit Ethernet switches that supported jumbo frames up to 9K. We started with these companies because their products are widely available and chose 8 ports because of the price point and, well, because having those extra ports is cheap insurance for probable network expansion. After perusing the Pricegrabber listings, we decided to also ask Belkin and Trendnet to submit their products to add a bit of variety. In all, we ended up with six switches, because Netgear decided to submit two products.

Since these are all "dumb" or unmanaged switches, there are no functional features to review. So I’ll dispense with the usual walk through of each product and distill the few differences among the products into Table 1.

Product Price Ports Switch Chip
Belkin
F5D5141-8
[Website]
$72.42 – $222.59
Check price
Rear Vitesse VSC7388
D-Link
DGS-2208
[Website]
$48.48 – $82.63
Check price
Rear Vitesse VSC7388
Linksys
SD2008
[Website]
$60.08 – $119.99
Check price
Rear Broadcom BCM5398
Netgear
GS108
[Website]
$60.20 – $134.48
Check price
Front Broadcom BCM5398
Netgear
GS608
[Website]
$54.99 – $125.88
Check price
Rear Broadcom BCM5398
Trendnet
TEG-S8
[Website]
$35.99 – $53.00
Check price
Rear Broadcom BCM5398
Table 1: Switch Feature Summary

I tried to get switches with a variety of chipsets, but it seems like Broadcom is the chip of choice for two of the "big three". D-Link also uses a Vitesse 5 port gigabit switch (VSC7385) in its DIR-655 draft 11n wireless router [reviewed here]. I was surprised to find no products using Marvell switches.

You can get a closer look at the products at each of their websites (linked in Table 1) if the opening group shot (or its larger version) doesn’t meet your needs. Internal board shots can be found in this slideshow, along with board design commentary.

Check out the slideshow See the slide show for the inside details on each switch.

Performance

My performance testing was quick and dirty, since a true switch performance test would require a Spirent SmartBits test platform or its equivalent, which I don’t have access to. I used two computers with 2.4 GHz Pentium 4 and AMD Athlon 3000+ processors, both running Windows XP SP2. Yes, I know that the Windows TCP/IP stack isn’t the fastest, but it’s what I had handy. (Pummel me in the comments if that’s what you enjoy…)

The gigabit adapters in each machine were Intel PRO/1000 MT Desktop PCI cards with 8.9.1.0 drivers downloaded from Intel’s support website. I tried both 4 and 9K jumbo frame settings, but settled on using 4K, since it seemed to work best with my setup. Short (under 6′) CAT 5e cables were used to connect each computer to the switch.

I ran separate transmit and receive tests using IxChariot, with the console and Endpoint 1 running on the P4 machine. So the data directions are with respect to the Intel system. I used the IxChariot high_performance_throughput script, running 1 minute tests in each direction using TCP/IP. This script uses a 10,000,000 byte filesize and 65,535 byte send and receive buffers and blasts data as fast as it can.

Figures 1 and 2 plot the average transmit and receive throughputs reported by IxChariot for the six switches. They also include reference runs using the same two computers connected via a 100 Mbps switch and the same two CAT 5e cables attached to each machine connected via a generic, i.e. not bandwidth or Category rated, RJ45 inline coupler. The Gigabit Straight cable runs were done without jumbo frames and with 4K jumbo.

Transmit Performance Comparison
Click to enlarge image

Figure 1: Transmit Performance Comparison

Figure 1 clearly shows three things:

  • There is a significant difference (~20%) between not using jumbo frames and 4K jumbo frames
  • There is little difference among switches
  • Best-case % throughput loss is significantly less for 100 Mbps than gigabit Ethernet (7% vs. 30%)

Table 2 summarizes the percent of throughput loss for each switch and the no jumbo frame case, using the straight cable, 4k jumbo frame test as a reference. All transmit results are within 5%, which I think can safely be said to be within measurement resolution.

Product Transmit (Mbps) % Loss
Gigabit Straight cable -no jumbo 551.7 20%
Linksys SD2008 658.2 5%
Belkin F5D5141-8 666.8 4%
Trendnet TEG-S8 671.8 3%
Netgear GS108 685.4 1%
D-Link DGS-2208 685.7 1%
Netgear GS608 692.7 0%
Gigabit Straight cable – 4k jumbo 692.5
Table 2: Transmit throughput relative loss

Similar conclusions can be reached using Figure 2 and Table 3, which summarize receive test results.

Receive Performance Comparison
Click to enlarge image

Figure 2: Receive Performance Comparison

Receive loss is a bit of a puzzle, since the percentage throughput reduction for the Belkin and Linksys switches is twice that of the other switches. But I’m reluctant to attribute the loss to anything other than measurement error, since both Vitesse and Broadcom-based products show higher losses.

Product Receive (Mbps) % Loss
Gigabit Straight cable -no jumbo 578.6 23%
Belkin F5D5141-8 668.8 12%
Linksys SD2008 689.5 9%
D-Link DGS-2208 728.6 4%
Netgear GS108 734.4 3%
Trendnet TEG-S8 734.5 3%
Netgear GS608 742.7 2%
Gigabit Straight cable -4k jumbo 755.8
Table 3: Receive throughput relative loss

Closing Thoughts

So there you have it. It’s nice to see that manufacturers have gotten the word that jumbo frames count, even if only for bragging rights and to make a potential sale-killer go away. Every one of these switches automatically supports jumbo frames up to 9K, although it would be nice if Linksys and Belkin added this information to product boxes and the information posted on their websites.

Note that when consider the throughput loss data you have seen, your mileage may vary for jumbo frame performance improvement and actual throughput obtained. Pumping bits along at gigabit speeds demands much more from your OS, computer bus architecture (and speed!) and TCP/IP stack. So those of you with speedier machines than mine might see faster speeds and lower throughput loss.

But what won’t make a difference is the switch you choose. You can buy any of these products and feel confident that they aren’t a throughput bottleneck.

Check out the slideshow Be sure to see the slide show for the inside details on each switch.

Related posts

TP-LINK TL-PA8030P KIT 3-Port Gigabit Passthrough Powerline Starter Kit Reviewed

TP-LINK's TL-PA8030P 3-Port Gigabit Passthrough Powerline Starter Kit combines performance and convenience in a top-ranked HomePlug AV2 MIMO adapter.

ZyXEL GS1200-8HP 8-Port Web Managed PoE Gigabit Switch Reviewed

ZyXEL's GS1200-8HP is an inexpensive and easy to configure PoE-enabled smart switch.

LG-Ericsson ES-2026 Smart Switch Reviewed

Updated - LG-Ericsson's ES-2026 has a nice admin interface, but needs a few minor fixes and slightly lower price.