Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Router Charts

Click for Router Charts

Router Ranker

Click for Router Ranker

NAS Charts

Click for NAS Charts

NAS Ranker

Click for NAS Ranker

More Tools

Click for More Tools

LAN & WAN Reviews

Performance - Noise Immunity

While I had things set up in Location A, I also ran noise immunity (or susceptibility) tests. I used two noise sources: a compact travel hairdryer (broadband noise) ; and a halogen floor lamp with dimmer (impulse noise). For a worst-case test, I moved the tested adapters to a non-surge-protected outlet strip and plugged the noise source into the same strip.

My previous experiences had shown HomePlug AV products to be more susceptible to impulse than broadband noise. But when I started an IxChariot stream then ramped the floor lamp up and down with the dimmer, I didn't see any effect on the plot.

Using the hairdryer, however, was a different story. Figure 9 shows an almost 20% drop in throughput with the broadband noise source on. The good news is that throughput recovered within a second or so once the noise stopped.

Belkin broadband noise effect

Figure 9: Belkin broadband noise effect

With the NETGEAR pair, however, the opposite was true. Figure 10 shows an IxChariot plot for the NETGEAR adapters. The hairdryer had no observable effect on throughput when it was turned on an off during the 10 - 20 second part of the plot. But you can clearly see throughput knocked down by, again, almost 20% when the lamp dimmer was ramped up and down. Note that recovery time took seconds after the lamp was turned off.

NETGEAR impulse noise effect

Figure 10: NETGEAR impulse noise effect

Interoperability

I only ran a quick interoperability check with a NETGEAR XAV1004 and a Belkin adapter plugged into the same wall outlet in my office. Figure 11 shows I got just shy of 44 Mbps vs. the 60 Mbps obtained between the two NETGEAR HomePlug AV adapters. Not bad, but not as good as, at least the two NETGEAR adapters paired up.

Belkin, NETGEAR Interoperability - Location A
Click to enlarge image

Figure 11: Belkin, NETGEAR Interoperability - Location A

More LAN & WAN

Wi-Fi System Tools
Check out our Wi-Fi System Charts, Ranker and Finder!

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Over In The Forums

https://fccid.io/MSQ-RTAXI600
It appears that in the router settings/ui, this is under Firewall>Network Services Filter, but there are a few boxes that I am unsure how to fill, spe...
I am pleased to announce the release of CakeQOS-Merlin!Current Version: 1.0.2 (Changelog)CakeQOS-Merlin is a custom add-on for supported Asus routers ...
HiMy log is populated by noisyAug 12 02:36:46 RT-AX88U-OL hostapd: eth6: STA 84:25:19:72:7c:a0 IEEE 802.11: associatedAug 12 02:36:46 RT-AX88U-OL kern...
Here's a small sample:Code: Aug 11 04:37:38 kernel: [BLOCKED - INBOUND] IN=eth0 OUT= MAC=34:a3:95:8c:4b:38:00:01:5c:9d:b2:46:08:00 SRC=139.59.58.115 ...

Don't Miss These

  • 1
  • 2
  • 3