Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Router Charts

Click for Router Charts

Router Ranker

Click for Router Ranker

NAS Charts

Click for NAS Charts

NAS Ranker

Click for NAS Ranker

More Tools

Click for More Tools

NAS How To

The LSI Logic MegaRAID Card

The LSI Logic MegaRAID adapters are ROM-based. So the usage model is to boot the computer and then start the controller's software with a control-key sequence. The controller's software is a BIOS-style menu-driven interface that allows you to set up, upgrade, or repair your RAID 5 array. When your computer boots up, you will see the LSI Logic adapter's control instructions flash on your monitor, as shown in Figure 1.

Figure 1: Splash screen

Figure 1: Splash screen

When you press <Ctrl>+M in response, the LSI Logic MegaRAID will start its software from ROM to allow you to manage your RAID 5 array. Figure 2 shows the main menu of the MegaRAID software.

 Figure 2: MegaRAID main menu

Figure 2: MegaRAID main menu

Figure 3 shows how menus pop up in the MegaRAID software.

Figure 3: MegaRAID menu pop-ups

Figure 3: MegaRAID menu pop-ups

Note that in Figure 3 I have moved the cursor to "Configure" and then pressed the <Enter> key, to pop up the "Configure" menu. I then moved the cursor to "New Configuration" to initialize the RAID 5 array of drives. The MegaRAID software has then popped open a third menu that says "Proceed?". To finish configuring a new array I would then move the cursor to "YES" and hit <Enter>. While the interface is a flashback to the days of MS-DOS, it is functional and reliable.

The MegaRAID cards allow what I call the "sane" RAID 5 repair procedure:

Step 0: Hear the shrill wailing of the MegaRAID card
Step 1: Identify which hard drive has failed
Step 2: Shut down the RAID NAS
Step 3: Remove the failed hard drive
Step 4: Get in your car
Step 5: Drive to your local computer retailer and buy a replacement hard drive
Step 6: Return home
Step 7: Install the new hard drive
Step 8: Kick off the RAID controller's recovery procedure
Step 9: When the recovery is complete, reboot the server and carry on

I named this the "sane" procedure after looking at software RAID and concluding that recovering a drive under software RAID was (for me) insane.

More NAS

Wi-Fi System Tools
Check out our Wi-Fi System Charts, Ranker and Finder!

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Over In The Forums

My custom VPN configuration would be 577 bytes long.However, this does not fit completely into the input field.I just happened to see that because a s...
So I recently picked up a TP-Link EAP245 V3 Just due to the amount of devices its easier to just have 1 ssid for both the 2.4&5GHz networks. But my is...
Hi, I can not use IGMP proxy on my AX88U with the last Merlin firmware, I got this message : "Due to hardware limitation, IGMP proxy cannot co-exist w...
Hi allI do really need your support as I believe I am almost there, but I don't manage to find a solution So, long story short, I have the same issue ...
It seems like I can't use a router (RT-AC56U) in AP mode as a DHCP server. Is that correct?Reason for asking: a family member has a pretty limited rou...

Don't Miss These

  • 1
  • 2
  • 3