Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Router Charts

Click for Router Charts

Router Ranker

Click for Router Ranker

NAS Charts

Click for NAS Charts

NAS Ranker

Click for NAS Ranker

More Tools

Click for More Tools

Wireless How To

Get the WRE54G Connected, Steps 1 & 2

We're first going to get the WRE54G connected to your wireless LAN. After we get a successful connection, we'll go back and secure the WRE54G.

Step 1: Reset the WRE54G to factory defaults

Use the reset button in the hole on the side of the Expander. Push and hold the button until you see the Link light turn steady red. If the Link light starts flashing and/or turns blue, repeat the reset until you get a steady red Link light.

Step 2: Connect to the WRE54G from a wired client

You will need a computer that can connect to the WRE54G via Ethernet. You might be able to get a reliable wireless connection to the WRE54G, but using a cable guarantees the connection. Note that it doesn't matter where the WRE54G and computer physically are for this procedure. They just both need to connect to the same LAN.

Note!NOTE: If you are using an access point instead of a wireless router, you connect the computer you'll be using to the LAN switch that the access point is connected to instead of the switch built into the wireless router.

The WRE54G comes set to a default IP address of 192.168.1.240 (some versions use 192.168.1.245). If your LAN has an IP range other than 192.168.1.XXX, you'll need to temporarily set the computer's IP address to one in the 192.168.1.xxx range.

TIP TIP: Write down the old settings or make a Restore Point (if you are using Windows XP) before making any changes. That will make it easy to restore your settings when you are done.

A) On Win XP navigate to Start > Control Panel > Network Connections and open the Connection properties for the computer's Ethernet adapter. Change your computer's IP address info to one in the 192.168.1.XXX range (such as 192.168.1.239) with a subnet mask of 255.255.255.0. (The Gateway and DNS settings won't matter for now and you can leave them blank.

B) Open a web browser and type in: http://192.168.1.240. Log in using a blank username and the password admin. You should see the WRE54G Setup screen (Figure 1).

WRE54G setup screen
Click to enlarge image

Figure 1: WRE54G setup screen

C) Change the WRE54G's Wireless IP address from 192.168.1.240 to something in your LAN's IP range. Make sure that it is outside the range of your LAN's DHCP server. Write down the new address!

Example: Your LAN uses the 10.168.3.XXX range with the DHCP server handing out addresses from 10.168.3.100 to 10.168.3.150. The WRE54G can be set to an IP address of 10.168.3.1 to 10.168.3.99 or 10.168.3.151 to 10.168.3.254.

D) Save the WRE54G settings. Since the WRE54G now has a new IP address in a new subnet, you won't get a "Settings changed" page in your browser. Wait about 10 seconds to ensure that the settings were saved, then power cycle the WRE54G to get the WRE54G to use the new settings. (Power cycling means unplug power from the WRE54G, wait about 5 seconds, then reapply power.)

E) Change your computer back to its previous IP address in your LAN's IP address range and enter that address into your web browser. You should now be able to connect to the WRE54G at its new address. If you can't, try power cycling the WRE54G and try connecting again. If you still can't connect, reset the WRE54G to factory defaults using the recessed reset button and try repeating the address change.

More Wireless

Wi-Fi System Tools
Check out our Wi-Fi System Charts, Ranker and Finder!

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Over In The Forums

Aquantia has a new firmware update out for the AQC100, AQC108, AQC107 and AQN100, AQN108, AQN107https://www.aquantia.com/support/driver-download/The f...
I have an AC68u and I put two fans behind it to cool it off. I used a double-sided tape to attach the fan but it fell off after three days.I saw some ...
https://fccid.io/MSQ-RTAXI600
I am pleased to announce the release of CakeQOS-Merlin!Current Version: 1.0.2 (Changelog)CakeQOS-Merlin is a custom add-on for supported Asus routers ...
It appears that in the router settings/ui, this is under Firewall>Network Services Filter, but there are a few boxes that I am unsure how to fill, spe...

Don't Miss These

  • 1
  • 2
  • 3