Router Charts

Click for Router Charts

Router Ranker

Click for Router Ranker

NAS Charts

Click for NAS Charts

NAS Ranker

Click for NAS Ranker

More Tools

Click for More Tools

Wireless How To

I used to have a FAQ that explained how to re-purpose a wireless router as an access point (AP). But it occurred to me that some folks might be able to use a little more of a step-by-step, so here it is. I'm going to use the virtually ubiquitous Linksys WRT54G as the object of our conversion.

Step 1: Connect a computer that is set to obtain its IP address information automatically to a LAN port on the wireless router that you want to convert to an AP. If you don't know how to do this, Figure 1 shows the applicable Windows XP screens. (Get to the Network Connections window by Start > Settings > Network Connections.)

Checking for "Obtain an IP address automatically"

Figure 1: Checking for "Obtain an IP address automatically"

Log into the admin page of the wireless router that you want to convert to an access point. From here on, I'll call this the "AP".

Step 2: For simple, one segment LANs, there must be only one DHCP server. Your LAN's router has a DHCP server and you don't want the two to conflict. So turn off the DHCP server on the AP. In Figure 2, you can see that the DHCP server in the WRT54G AP has been disabled.

Shut off the DHCP server; change the IP

Figure 2: Shut off the DHCP server; change the IP

Step 3: Find your LAN Router's DHCP server range. Figure 3 shows the Basic Network Settings page of the D-Link DGL-4300 that is my LAN's router. This is where the DHCP server controls happen to be. Different routers might have the DHCP server controls on a separate page, so you may have to poke around a little.

LAN router settings

Figure 3: LAN router settings

The 4300 normally has its Router IP Address set to 192.168.0.1 by default. But you can see in Figure 3, I changed it to 10.168.3.254. This shifted the DHCP server to the 10.168.3.X subnet instead of the 192.168.0.X. I also could have used 10.168.3.1 or any address as long as it wasn't between 10.168.3.100 and 10.168.3.249, which is the DHCP server's range.

The bottom line is that the my LAN router's DHCP server range is 10.168.3.100 to 10.168.3.249.

Step 4: Change the address of the AP to an unused LAN IP address. This will ensure that you can reach the admin pages of the AP to change settings when needed. Referring back to Figure 2, you can see that I set the AP to 10.168.3.250. Again, this could be any IP from 10.168.3.1 to 10.168.3.99 or 10.168.3.250 to 10.168.3.254, which are all outside the LAN DHCP server range.

Step 5: Connect the AP to the LAN. Unplug the computer you used to configure the AP and plug it back into one of your LAN router's switch ports. Now take an Ethernet cable, plug one end into another unused router switch port and the other end into one of the AP's LAN ports. Be sure to use a LAN port and not the WAN port. Figure 4 shows the proper connection for the WRT54G.

 

AP connection detail

Figure 4: AP connection detail

Step 6: Check the AP LAN connection. You should now be able to use any of your LAN's computers to reach the AP. So open a browser, enter the address that you set for the AP in Step 4 (which is at 10.168.3.250 in this example) and you should get the login prompt.

If you don't get the prompt, recheck that you have the Ethernet cable running from LAN port to LAN port on your router's switch and the AP. The respective port lights on the router and AP should be lit.

Step 7: Check the AP wireless connection. Fire up a wireless notebook or other client and check that it properly associates and pulls an IP address from your LAN router's DHCP server. Congratulations! You now have a new AP!

Now use this article if you want to use your new AP to extend your current wireless network.

More Wireless

TRENDnet logo

How Powerline Can Solve Your Wi-Fi Woes - There's a better way to get WiFi Everywhere™.

Wi-Fi System Tools
Check out the new Wi-Fi System Charts, Ranker and Finder!

Featured Sponsors


Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Over In The Forums

Hi There,I'm running 382.1 on an ASUS 85u, and all my clients show up as MAC address and not computer name.Its only in the web console tho, when I use...
I just configured a new AC86U for OpenVPN connections. I am able to connect successfully. However I experienced random disconnect, from some seconds t...
Details on the blog:https://www.netgate.com/blog/pfsense-2-4-2-release-now-available.htmlMy web gui slowed to a crawl with 2.4 release. This release s...
My ISP speed, DL=370Mb, UL=22Mb.Web speed testing site = speed.netAll LAN cables are CAT5E or CAT648 port LAN switch = HP J9660AHP LAN switch connecte...
Hi all been a long time since I rapped at you.Want to stream steam games via vpn? My N66U's PPTP works like a charm (windows rdp will block the consol...

Don't Miss These

  • 1
  • 2
  • 3
Get Backblaze Now!