Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Router Charts

Click for Router Charts

Router Ranker

Click for Router Ranker

NAS Charts

Click for NAS Charts

NAS Ranker

Click for NAS Ranker

More Tools

Click for More Tools

Wireless Reviews

Performance - 802.11a

The WAG511's 11a throughput was surprisingly good, with Figure 12 showing much better performance than I've previously had with any 11a products.

NETGEAR WAG511 - 11a throughput

Figure 12: 802.11a throughput
(click on the image for a full-sized view)
I usually get a very unreliable connection, if any at all, at my Condition 3 and 4 locations with very "bursty" throughput. The difference, however, is not in the WAG511, but from the WAB102 AP's second-generation 11a radio. See my Second-generation 802.11a NTK for the story behind this improved 802.11a performance.

NETGEAR WAG511 - WEP and Turbo mode throughput

Figure 13: WEP and Turbo mode performance
(click on the image for a full-sized view)

I also ran tests in Turbo mode, and with WEP enabled in both normal and Turbo modes. Figure 13 shows an average throughput of about 31Mbps in Turbo mode under best case conditions. I also ran tests at all four of my test locations and found that, unlike my previous tests, Turbo mode still produced an approximately 40% throughput increase even under weaker signal conditions. You can also see that WEP-enabled performance is virtually identical to running without it.

In all, a very impressive performance in all modes.

802.11a Wireless Performance Test Results

Test Conditions


- WEP encryption: DISABLED
- Tx Rate: Automatic
- Power Save: Disabled
- Test Partner: NETGEAR WG602 54Mbps Wireless Access Point

Firmware/Driver Versions

AP f/w:
1.04.00
Wireless client driver:
2.3.0.73 WinXP
Wireless client f/w:
No Info

Test Description Signal Quality (%) Transfer Rate (Mbps) Response Time (msec) UDP stream
Throughput (kbps) Lost data (%)
Client to AP - Condition 1 100 19.3
[No WEP]
18.6
[w/ WEP]
1 (avg)
2 (max)
499 0
Client to AP - Condition 2 95 19.2 1 (avg)
3 (max)
499 0
Client to AP - Condition 3 73 19.3 1 (avg)
5 (max)
499 0
Client to AP - Condition 4 68 17.5 2 (avg)
5 (max)
499 0
See details of how we test.

More Wireless

Wi-Fi System Tools
Check out our Wi-Fi System Charts, Ranker and Finder!

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Over In The Forums

Hi There,Update 2020/08/06386 rc2-3 firmware is in this linkhttps://drive.google.com/drive/folders/154vHdrYh_rGP_qFooHgAkzXSJchge7Ue?usp=sharingChange...
I plan to make available a beta version of the next kamoj add-on - if there is enough interest.N.B: Voxel firmware is a pre-requisite, not an option!I...
I was doing some research and was seeing a lot about issues with the 2.4ghz band not working after a while or having very short range (or poor perform...
No matter what I put for upload/download bandwidth on a new RT-AX88U on Merlin 384.18, it will peg the upload speed at my ISP's maximum speed and ping...
Hi to all!I just installed Pyload and Transmission on my RT-AC86U. Now I have a problem. I have to set the router (192.168.1.1) to go to Internet thro...

Don't Miss These

  • 1
  • 2
  • 3