Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Router Charts

Click for Router Charts

Router Ranker

Click for Router Ranker

NAS Charts

Click for NAS Charts

NAS Ranker

Click for NAS Ranker

More Tools

Click for More Tools

Wireless Reviews

Setup, Administration, & Basic Features

Belkin doesn't bother with supplying a software setup utility, opting instead to use the 7130's browser admin interface for initial setup.

The AP comes set to 192.168.2.254 (subnet 255.255.255.0) as its factory default, so you'll need to make sure the computer that you're running the browser on is setup in the 192.168.2.X subnet.

Tip TIP: Try setting your computer to 192.168.2.200 (or any other 192.168.2.X address except 192.168.2.254 ), subnet 255.255.255.0. You'll probably need to reboot, too, or "Repair" the connection if you're running WinXP.

Once you get your computer and the AP in the same subnet, open your browser and enter the default IP address, and you'll get the home screen shown in Figure 2.

Belkin F5D7130 - Home screen

Figure 2: Home screen
(click on the image for a full-sized view)

Note that I didn't say you were first presented with a login prompt. Belkin has chosen to leave admin security for the 7130 wide open, presumably to make things easier for home users to set up. Although you could argue that Belkin's choice of no password is essentially the same as having the common choices of "admin", "1234", "password", etc. that other products use, I think it's a less secure choice. In any case, password or not, anyone knowing the AP's IP address can always view the Home screen, which although handy, is also not good security practice.

The interface is generally quick, with under 5 second saves for the changes you make on each page. A longer 10 - 15 second save is required when you make changes to the Bridging settings (more later). Multiple admin logins are not allowed, and you'll get a warning that includes the IP address of the current administrator if you try. Once you're logged in, there's a default 10 minute idle timeout that you can change on the System Settings page, or you can use the Logout button when you're done.

I should note that although you can change the 7130's IP address and subnet mask, you can't have it act as a DHCP client and automatically pick up its IP address from your LAN's DHCP server. This isn't that big an omission as it may sound, since I recommend statically setting the IP address of access points anyway so that you always know where to reach them.

More Wireless

Wi-Fi System Tools
Check out our Wi-Fi System Charts, Ranker and Finder!

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Over In The Forums

This is my first post. Not sure if it's in the right place. My router Rt-ac68r running latest Merlin 384.11_2 has shown a strange connected clients ma...
Hi,I'm currently on the lookout for a router that is capable of delivering speeds of 1000/1000 mbps in a small apartment (~ 350 sq ft) with only a liv...
How does one? I cannot find any guide that really explains things.I get this error:*** Error: No ext2|ext3|ext4 partitions available. Exiting...So I n...
About how fast is the AC66U-B1 or AC86U? with HW acc Disabled? WAN throughput wise? I couldn't find much other than with it most likely turned on from...
Anyone knows what this is all about?avahi_key_new() failedI get this a lot not a while and them it stops.A search on the forum reviled nothing.I keep ...

Don't Miss These

  • 1
  • 2
  • 3