Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Router Charts

Click for Router Charts

Router Ranker

Click for Router Ranker

NAS Charts

Click for NAS Charts

NAS Ranker

Click for NAS Ranker

More Tools

Click for More Tools

Wireless Reviews

Wireless Performance

NOTE!NOTES
• Testing was done in a 1GHz Celeron notebook running WinXP home connecting to a NETGEAR ME102 802.11b Access Point
• Details of how we test can be found here.

I began my performance testing using NETGEAR's new WGT624, which uses Atheros' 802.11g chipset, as a test AP. The HWU associated without any problems, but try as I might, it would only connect at a 2Mbps rate. This resulted in a maximum throughput around 1Mbps. I next tried a Belkin F5D7130, based on Broadcom's 802.11g chipset, but obtained the same result - 2Mbps max connect rate with 1Mbps throughput.

When I reported the problem to Hawking, they said it was the first they'd heard of it and said they'd experienced no problems in tests with their own 802.11g products, which are based on GlobespanVirata's (Intersil) PRISM chipset. So I dug out a PRISM-based NETGEAR WG602, and confirmed that the HWU did, indeed, connect at 11Mbps and had throughput greater than 4Mbps.

Update 10/31/2003 Although Hawking is looking into possible solutions, they made no committments that the problem will be fixed. But they did say that they're planning to release an 802.11g version - dubbed the HWU54D - using Envara / Cypress Semi's USB G chipset at the end of November.

Experiments completed, I turned to my aged NETGEAR ME102 802.11b access point for the remainder of the throughput tests, which are summarized in Figure 6.

Hawking HWU36D - Four location throughput

Figure 6: H-WU36D via NETGEAR ME102 throughput
(click on the image for a full-sized view)

For each test location, I played with antenna orientation to obtain the best signal. I found that the antenna was, as expected, directional and had best performance when its front was aimed in the general direction of my access point. But I found that, contrary to the information in Figure 3, I also got a useable, although not as good, signal when the back of the antenna was oriented to the access point. Pointing either side of the antenna panel pretty much killed the signal, however.

I found the Overall Connection Quality plot in Hawking's client utility (Figure 7) to be helpful in orienting the HWU for best signal.

Hawking HWU36D - Monitoring the connection

Figure 7: Monitoring the connection

The refresh rate was sufficiently fast and the combination of instantaneous and time-based performance indicators gave me the required feedback for careful antenna aiming. The shot in Figure 7 was taken at my test location 2 and shows the signal strength variation over a 180 degree spin of the HWU. (The antenna was set to a vertical position and I started with the antenna back aimed at my test AP.)

Finally, note that there's no throughput hit when enabling WEP. But like most other 802.11b products, the HWU doesn't support Wi-Fi Protected access, either.

More Wireless

Wi-Fi System Tools
Check out our Wi-Fi System Charts, Ranker and Finder!

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Over In The Forums

I run an OpenVPN client on my ASUS RT-AC86U with 384.10_2 firmware. Everything works fine except that whenever the VPN client disconnects (happens occ...
Hey guys; so obviously I can add my wifi printer to any particular SSID, but is there a way I can make it available to any device, regardless of which...
This is really annoying. I bought an Archer A7 because it was wirecutter's top pick for a home wifi router and bonus it has parental controls and can ...
I just logged in and saw 1 core being maxed.Some rouge process has glitched and I have no idea how long it was pegged use a full cpu core.A script iss...
I can obviously ping the gateway from any device, but regardless of whether I turn on "guest" access to the share (or use username/pw), or try it with...

Don't Miss These

  • 1
  • 2
  • 3