Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Router Charts

Click for Router Charts

Router Ranker

Click for Router Ranker

NAS Charts

Click for NAS Charts

NAS Ranker

Click for NAS Ranker

More Tools

Click for More Tools

Wireless Reviews

Introduction and Product Details

SMC EZ Connect g 2.4GHz Wireless Ethernet Adapter

SMC EZ Connect g 2.4GHz Wireless Ethernet Adapter
Summary PRISM based 802.11g multimode device. Can operate as bridge or AP with WDS-based bridging.
Update 12/20/2003 - Removed references to supporting WPA in AdHoc mode
Pros • Can run as an AP with WDS-based bridging / repeating or wireless Bridge
• Supports WPA in bridge mode
Cons • Firmware load required to switch between AP and Bridge modes
• Non-upgradeable antennas
• WPA in Bridging mode not robust

SMC's SMC2870W is a product that seems to be having an identity crisis. The silkscreen on the product says "EZ Connect g 2.4GHz 54Mbps Wireless Ethernet Adapter SMC2870W", but its User Manual, web page and product brochure refer to it by that moniker and also as a "Wireless Ethernet Bridge".

In fact, the 2870W can function as an 802.11g access point that supports WDS-based wireless bridging and repeating. But it also functions in what SMC calls "Bridge" mode, but which functions more like an 802.11g Ethernet adapter capable of operating in Infrastructure and Ad Hoc modes.

The 2870W comes in a plastic SMC-grey enclosure with a footprint slightly smaller than a VHS cassette, sloped front and sides, and mounting screw slots on its bottom. The PWR, wireless Tx / Rx, and Ethernet Link / Act indicators are on the sloped front of the box and are somewhat dim when viewed when the unit is sitting on a shelf at eye-level. Power and 10/100 Ethernet connectors and a Reset / Reset-to-Defaults switch are all on the rear panel.

Tip Tip: The 2870W's Ethernet connection does not support auto MDI / MDI-X, nor does it have a Normal / Crossover switch, so setup can require some experimentation depending on the mode you're using and what you're connecting to. SMC thoughtfully includes a crossover cable (although it's not identified as such), but not a normal UTP cable.

The product is based on Ubicom's IP2022 Network Processor and uses a AirVast Technology WN360g mini-PCI radio based on Intersil / GlobespanVirata / Conexant's PRISM GT chipset (Figure 1).

SMC2780W - Radio

Figure 1: The radio
(click on the image for a full-sized view)

The radio is connected to two hard-wired external dipole antennas, but since the antennas connect to the board via miniature connectors, die-hard hackers could always rig up higher-gain substitutes.

Examination of the board revealed that the 10/100 Ethernet connector is wired to support Power over Ethernet (PoE) use, although SMC neither specifies nor supports this option.

More Wireless

Zyxel logo

Wi-Fi Mesh System Secrets - Here's how to get the most out of your whole home mesh WiFi system.

Wi-Fi System Tools
Check out the new Wi-Fi System Charts, Ranker and Finder!

Featured Sponsors



Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Over In The Forums

Is it possible to control LAN access via iptables? I have a bunch of IOT devices that I want to access the internet and (and this is the kicker) accep...
I recently enabled the statistics for traffic analyzer, and in the list of clients I was seeing this mac address I couldn't find on my network , I fou...
just a quick question, I have an rt-ac56u with 378.55 firmware on it, is it possible to update from 378.55 to 384.5 or is this too much of a jump??
HelloSorry if this is a repost of the same topic somewhere else.Im having issues when looking for devices at the traffic analizer page. I can see all ...
Hi all I have to put a new iptable rule. For that I have created a script and named it "firewall-start" and located it under /jffs/scripts/If I run th...

Don't Miss These

  • 1
  • 2
  • 3