Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Router Charts

Click for Router Charts

Router Ranker

Click for Router Ranker

NAS Charts

Click for NAS Charts

NAS Ranker

Click for NAS Ranker

More Tools

Click for More Tools

Wireless Reviews

Wireless Tests - Mixed and Neighboring WLANs

I didn't spend much time checking out how well the N1 router supported other flavors of wireless clients. My previous draft 11n product interoperability tests told me that I probably would be able to associate clients with the N1 router just fine, and that other draft 11n or 11g products would at best operate at 11g rates, i.e. around 20 Mbps.

Turns out that's pretty much what I found. I tried a Linksys WPC54G 802.11b/g Cardbus card based on Broadcom's Airforce 11g chipset and Belkin's own "Pre-N" Cardbus card that uses the first-generation Airgo "True MIMO" chipset. Figure 23 shows the results from the "Pre-N" card run.

Belkin Pre-N client with N1 router - Up and Down throughput

Figure 23: Belkin Pre-N client with N1 router - Up and Down throughput (click to enlarge)

As expected, total average throughput would come in around 20+ Mbps, if it weren't for the throughput dropout problem which appears to carry over into non-xspaN clients. I obtained similar, but slightly higher, results with the Broadcom-based WPC54G card.

As an additional test, Netgear's SPH101 Skype Wi-Fi phone was able to associate and work just fine with the N1 acting as an AP.

After my disappointment with the N1's throughput variation and security mode throughput loss, I was pleasantly surprised by the results of my "bad neighbor" (adjacent WLAN interference) check. To recap the method, I set up an 802.11g WLAN comprised of a Linksys WRT54G router and WPC54G Cardbus card in the same room as the N1 Both routers are set to function as APs, are set to Channel 6 and are connected to my LAN so that the IxChariot console can control everything.

Figure 24 shows that the N1 cooperates very well when running uplink traffic, quickly dropping its throughput in the presence of 11g traffic. I presume that the N1 switched from its 40 MHz channel-bonded mode to its 11b/g compatible 20 MHz mode, but since the card driver doesn't appear to update its link status information I couldn't confirm this.

"Bad neighbor" test results - uplink

Figure 24: "Bad neighbor" test results - uplink (click to enlarge)

Figure 25 shows similar "good neighbor" behavior with downlink traffic.

"Bad neighbor" test results - downlink

Figure 25: "Bad neighbor" test results - downlink (click to enlarge)

Needless to say, I'm very pleased to see these results, especially from Atheros. Their experience with Super-G should have given them the technology to be able to constantly keep track of what's happening on the airwaves in between transmissions, and it appears that it has. So right now, Atheros xspaN is the only neighbor-friendly draft 802.11n technology.

More Wireless

Wi-Fi System Tools
Check out our Wi-Fi System Charts, Ranker and Finder!

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Over In The Forums

I have an Intel NUC8 as my Plex server, and I'm trying to get it to automatically WOL on network requests to its IP on the Plex port (32400 IIRC). I h...
Hello all: I've just bought a PCE-AC88 card, because my powerline adapters are getting 40-50 mbps out of the 120 mbps connection. Sadly I can not get ...
This morning our spectrum service is out _again_. This is happening twice a week now and I'm betting that if I call tech support will blow me off with...
Hi, what is your opinion of ZenWiFi AX (XT8)?I currently have ASUS RT-AC68U but I would like to enhance my wifi coverage with new mesh capable router....
Hi, So I purchased two RT-AC86U routers to handle my connection, I was planning on using the 2nd as a AiMesh node but to be honest I'm getting better ...

Don't Miss These

  • 1
  • 2
  • 3