Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Router Charts

Click for Router Charts

Router Ranker

Click for Router Ranker

NAS Charts

Click for NAS Charts

NAS Ranker

Click for NAS Ranker

More Tools

Click for More Tools

Wireless Reviews

Velop Dual-band Intelligent Mesh WiFi System
At a glance
ProductLinksys Velop Dual-band Intelligent Mesh WiFi System (WHW0103)   [Website]
SummaryDual-band, lower cost version of tri-band Velop without the second 5 GHz radio
Pros• Decent routing feature set
• Supports AP mode and Ethernet backhaul
• Supports 802.11k and v roaming assist
Cons• Poor performance
• No band steering

Typical Price: $250  Buy From Amazon

Introduction

It's been pretty quiet on the consumer Wi-Fi front lately. The dearth of new products is mostly due to companies working feverishly behind the scenes to ready their draft 11ax products. ASUS and D-Link have already shown their hands, and I suspect Linksys, NETGEAR and perhaps others may be making announcements either at Computex Taipei in a few weeks, or shortly after.

In the meantime, Linksys has started shipping the lower cost version of its Velop Wi-Fi system that it announced at CES in January. The Velop Intelligent Mesh WiFi System aka Velop Dual-Band, shaves around $130 off the price of a three-pack by dropping the second 5 GHz radio. The result is a another Qualcomm-based dual-radio three-pack Wi-Fi mesh system intended to lure potential Google Wifi buyers with its lower price.

Velop DB has the same square-to-round tower form factor and approximately 3" x 3" footprint as Velop TB (Tri-band), but it's notably shorter (5.5" vs. 7.3"). It comes only in white, but in one, two and three-pack SKUs. I tested the three-pack.

The callouts show the single status LED is still there...

Linksys Velop LED callout

Linksys Velop LED callout

...but the dual Gigabit Ethernet connectors have been moved to the back. This may reduce WAF a bit due to higher cable visibility, but it's a helluva lot easier to connect to.

Linksys Velop connector callout

Linksys Velop connector callout

Velop can use Ethernet as backhaul, but this option still isn't part of the app's setup process. You'll just need to set everything up first using wireless backhaul, then connect the desired nodes to Ethernet. You can also bypass Velop DB's NAT router and run the system as APs by choosing Bridge mode in the Internet connection setup controls.

Inside

Velop DB's FCC documents are under wraps for awhile. So after testing was done, I opened one of the nodes up for a look. Besides dropping the second 5 GHz radio, Linksys has also made a few other changes to come up with the DB.

RAM has been cut in half to 256 MB and flash put on a crash diet, dropping from 4 GB to 256 MB. The DB also has a Qualcomm IPQ4018 vs. the IPQ4019 found in the TB and uses different external components.

The board photo shows a single set of printed circuit dual-band antennas sitting in the black frame at photo left are driven by combined 2.4 and 5 GHz RF chains. The antennas sit at the top of the tower when everything is put back together. A separate 2.4 GHz antenna (not shown) for the Bluetooth 4.1 radio sits lower in the tower.

Linksys Velop DB board - side 1

Linksys Velop DB board - side 1

A similar approach is taken in the TB design, which has filters on the 5 GHz chains to separate the low and high band radios.

Linksys Velop TB board - side 1

Linksys Velop TB board - side 1

There's not much to see on the other side of the DB board, aside from the 256 MB of DDR3 RAM and CSR 8811 Bluetooth 4.1 radio SoC.

Linksys Velop DB board - side 2

Linksys Velop DB board - side 2

This is in constrast to the TB, which has another 5 GHz radio on its backside.

Linksys Velop TB board - side 2

Linksys Velop TB board - side 2

The table below summarizes the DB's components along with the TB and Google Wifi's for comparison. Note the Zigbee radio that was never enabled on the TB isn't included in the DB.

  Linksys Velop Dual-band Linksys Velop Tri-band Google Wifi
CPU - Qualcomm IPQ4018 quad-core Wave2 2x2 a/b/g/n/ac SoC - Qualcomm IPQ4019 quad-core Wave2 2x2 a/b/g/n/ac SoC - Qualcomm IPQ4019 quad-core Wave2 2x2 a/b/g/n/ac SoC
- STM32F072 32 bit ARM Cortex-M0
- Infineon STM9615 Trusted Platform Module
Switch QCA8072 QCA8072 QCA8075
RAM 256 MB Winbond W632GU6MB 512 MB 512 MB
Flash 256 MB Winbond W25M02GV 4 GB Samsung KLM4G1FEPD - 4 GB eMMC (IF5055?)
-4 MB Winbond 25Q64FV
2.4 GHz Radio - In IPQ4018
- Skyworks SKY85330-11 2.4 GHz Front End (x2)
- In IPQ4019
- MSC5533621E (maker unknown) 2.4 GHz power amp (x2)
- In IPQ4019
- Skyworks SKY8530 2.4 GHz front end (x2)
5 GHz radio - In IPQ4018
- Skyworks 5 GHz Front End [marked SKY7482I001] (x2)
- In IPQ4019
- Skyworks SKY85408-11 5 GHz Power Amp (x2)
- In IPQ4019
- Skyworks SKY85717-11 5 GHz front end (x2)
5 GHz radio #2 -N/A - QCA9886 2x2 a/n/ac SoC
- Skyworks SKY85408-11 5 GHz Power Amp (x2)
N/A
Bluetooth CSR 8811 Bluetooth 4.1 radio SoC CSR 8811 Bluetooth 4.1 radio SoC Qualcomm 3003-CL3D (CSR102x?)
ZigBee -N/A - Silicon Labs EM3581 ZigBee / Thread SoC
- SiGe 2432L 2.4 GHz ZigBee front end
- Silicon Labs EM3581 ZigBee / Thread SoC
- Skyworks SKY66109-11 2.4 GHz ZigBee front end
Table 1: Component summary and comparison

Features

Velop DB's feature set is summarized in the tables below. Basically, no features have changed since the original Velop hit store shelves. Linksys says the app has been tweaked to improve the setup process, look better on iPhone X and squash bugs. The Channel Finder feature also handles networks with five or more nodes better. Band steering is still not supported, but 11k and v roaming assistance still is.

Features
# of Ethernet ports2
Max WAN Ports1
CPUQualcomm IPQ4019 quad-core SoC
RAM (MB)256
Flash (MB)256
Firmware1.1.5.187788
Cloud Service
N
Web Admin
Y
DHCP Reserve
Y
Ethernet backhaul
Y
AP Mode
Y
Wireless Bridge
Y
NotesAlso available as single node (WHW0101)
Wireless
System TypeMesh
# of Wi-Fi radios2
# of streams2
ClassAC1300
Wi-Fi Radio 12.4 GHz: In IPQ4019
Wi-Fi Radio 25 GHz: In IPQ4019
Wi-Fi Radio 3N/A
Bluetooth RadioCSR
IoT RadioNone
FCC IDQ87-03331
AntennaInternal
WPS
Y
RADIUS
N
MU-MIMO
Y
Guest Network
Y
Band Steering
N
AP Steering
N
Roam Assist11kv
Firewall
Port Forward
Y
DMZ
Y
Content Filtering
Y
Rogue Device Block
N
Threat Protection
N
Internet Pause
Y
User Accounts
Y
UPnP
Y
UPnP disable
Y
NotesUPnP controls available via web interface only
WAN
Static
Y
Dynamic
Y
PPPoE
Y
PPTP
Y
L2TP
Y
IPv6
Y
QoS
Device Priority
Y
Traffic Priority
N
DirectionUp

The other features are as described in the original Velop TB review. The updated User Guide has lots of app screenshots and describes most of the feature set. Note that Velop has a web admin GUI available at http://192.168.1.1. You'll have to jump through a few hoops to access it, but the GUI guides you through the process.

Once you're there, you can fiddle with the hidden advanced-wireless.html page if you dare.

Linksys Velop hidden Advanced wireless settings

Linksys Velop hidden Advanced wireless settings

The regular Wireless settings page will let you set a different SSID for each band, but you can't set operating channels.

Linksys Velop hidden Advanced wireless settings

Linksys Velop hidden Advanced wireless settings

Futz with this stuff at your own risk. Remember, you're supposed to leave the Wi-Fi driving to the System in Wi-Fi systems.

More Wireless

Zyxel logo

Wi-Fi Mesh System Secrets - Here's how to get the most out of your whole home mesh WiFi system.

Wi-Fi System Tools
Check out the new Wi-Fi System Charts, Ranker and Finder!

Featured Sponsors



Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Over In The Forums

I have my RT-AC5300 (merlin powered) setup as my primary devices connected to my modem, I have used one of my RP-68U in a wired AP mode setup.The 5300...
HelloI am new to networking and I apologize in advance if this has been asked and I was too naive to know what to search for.I live in Japan and I hav...
Hi,I have an RT-AC68U with Merlin 384.5.The list of List of Clients is restricted to a few wired devices (not the complete list) and no devices for th...
Hi,I installed a NVR(Network Video Recorder), and I want to setup VPN for that.(I want to see it remotely and securely), and of course I want to setup...

Don't Miss These

  • 1
  • 2
  • 3