Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Wi-Fi Router Charts

Click for Wi-Fi Router Charts

Mesh System Charts

Click for Wi-Fi Mesh System Charts

Hands On

Once your device has connected to your network and to, you'll land at the screen shown on the left in the composite image below. This provides a top level status of each of your Smart Plug devices. If you have more than one Smart Plug associated with your mydlink account, each one will appear on this screen.

This screen shows that "Lamp" is currently turned on, the power being supplied to the load that's plugged in is 49 watts, and the temperature of the Smart Plug is 118 F. The power icon on the left toggles the power on/off. If the plug is turned off, the status disappears and is replaced with "Off".

D-Link DSP-W215 landing page and top level menu

D-Link DSP-W215 landing page and top level menu

If you tap on the right ">" next to the temperature, the screen shown on the right will appear. For this screenshot, I scrolled down so that the four sub menus would be visible. The label for the switch, "Lamp" has scrolled off the top. With a little better design, I would think that everything on this screen should fit on a single screen without scrolling.

I'll comment on each of the four menus briefly. Be sure to check out the gallery for screenshots from each of the menus.

Power - In this menu, you can create a monthly power budget for the device(s) plugged into the Smart Plug. The chart shows daily power consumption along with a graph showing percentage of the total power budget consumed. Optionally, you can choose to turn off power when the monthly power usage exceeds the limit. You can also choose the day of the month to use for the billing date as well as set a notification warning level.

Temperature -This is a really simple menu. You can enable/disable overheat protection as well as an overheat alert. In this menu, you also set the threshold for turning off power to the socket. It defaults to 158 degrees F.

Schedule - The Smart Plug schedule menu provides you with five schedules. The default names, all of which can be changed are In Home, Away, Customize 1, Customize 2 and Customize 3. Only one profile can be active at a time. Power on/off schedules can be set in half hour increments with multiple on/off times for each day. You can enable/disable reminders to notify you when an event is triggered and set the time zone. Notifications are delivered through the Smart Plug app.

Information - This page provides basic information about your Smart Plug including IP address, MAC address, current firmware version and product name. In this menu, you can change the name of the device, say from "Lamp" to "Floor Lamp" and perform a factory reset. This menu will also notify you of available firmware updates and will download/install the updates for you.

Initially, I had a problem during setup with the Smart Plug negotiating a WPS connection with my router. A power cycle of the router resolved that issue. I also set up the Smart Plug before I left on an extended trip. It worked fine, and I was able to connect to it, monitor power usage and change the status for about 10 days or so. Then it went offline. Upon returning home, I discovered that we had experienced a power outage and apparently the device didn't come back on line when power was restored. I unplugged it, moved it to my office, plugged it back in again and it reconnected.

I tested both the iOS and Android apps. As noted, the iOS app is designed for the iPhone. Both apps worked the same and featured the same UI. Testing the Android app didn't go as smoothly. When searching for the app on my Nexus 7, the Google Play store didn't return a match. It would appear that there might be separate version for Android tablets that's different than the version for Android phones. I experienced no problems with the Android app on my Razr Maxx.

When connecting remotely, you have the same access to the device as if you connected on the local network. The only difference I noticed was some additional latency due to a slow connection.

Closing Thoughts

Compared to my struggles with Belkin's WeMo Insight, I had a much more positive experience with D-Link's Wi-Fi Smart Plug. It was easy to set up, configure and use and worked well.

But as with all products, there's room for improvement. Though not implemented properly on the WeMo, I liked the concept of a sunrise/sunset schedule that would change the schedule automatically. From a security standpoint, I would also have liked the option of randomizing an event around a scheduled time. When lights come on at exactly the same time every night, it's sure sign to potential burglars that you're not at home. Going back to the days of my old X10 controllers, I remember that it would randomize on/off times around a scheduled time for just that reason.

In a larger environment where you might have multiple devices, the ability to log on/off events to a syslog server, including manually changing the power state by pushing the power button on the device, could be attractive feature for those using the devices for security purposes. Finally, the lack of either desktop apps or a web browser interface on the Smart Plug may be seen as a negative by some potential users.

In the end, the D-Link DSP-W215 delivers the features it promises. It installed easily, monitored power and turned attached devices on/off on schedule. If you're looking to wise up a plug or two around the house, I recommend the D-Link over the Belkin WeMo.

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Don't Miss These

  • 1
  • 2