Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Router Charts

Click for Router Charts

Router Ranker

Click for Router Ranker

NAS Charts

Click for NAS Charts

NAS Ranker

Click for NAS Ranker

More Tools

Click for More Tools

NAS Reviews

Introduction

At a Glance
Product Thecus YES Box (N2100)
Summary "Bring Your Own Disk" (BYOD) RAID dual-drive NAS with Gigabit Ethernet and media serving
Pros • RAID 0,1 and JBOD support
• Up to two SATA drives
• Gigabit Ethernet with 4K and 8K Jumbo frames supported
• Many Features
Cons • A bit on the pricey side for a box without drives
• No backup features

Thecus YES Box N2100

Thecus has been after me for awhile to retest its N2100 dual-drive NAS that Jim Buzbee first looked at back in June. They said the new firmware has significantly improved performance and wanted another crack at their position in our NAS Charts. So without further ado, here are the results of the retest.

Performance - 100 Mbps LAN - JBOD

As with all our NAS testing, IOzone was used to check out the file system performance on the N2100 (the full testing setup and methodology are described on this page). Tests were run in JBOD and RAID 1 modes with 100 and 1000 Mbps LAN connections. The gigabit-connected tests were run with both jumbo frame capability disabled and with 4k jumbo frames.

To ensure connection at the intended speeds, the iozone test machine and the N2100 were manually moved between a NETGEAR GS108 10/100/1000Mbps switch for gigabit-speed testing and a 10/100 switch for 100 Mbps testing.

NOTES:

  • Firmware version tested was 2.1.03
  • Drives used were two Seagate Barracuda ST3300831A 300GB 7200RPM SATA hard drives with 8MB of cache supplied by Thecus
  • Keep in mind that the maximum raw data rate for 100Mbps Ethernet is 12500 Kbytes/sec and 125000 Kbytes/sec for gigabit

Figures 1 and 2 show write and read results respectively with a 100 Mbps LAN connection and the N2100 configured in JBOD mode. (The N2100 also supports RAID 0 in addition to JBOD and RAID 1, but I didn't test that mode.) Included in the plots are the D-Link DNS-323 and HP Media Vault, which are recently tested dual-drive NASes with similar performance. I've also included data from the original test run, indicated by "Thecus N2100 original" in each plot.

100 Mbps LAN JBOD write performance

Figure 1: 100 Mbps LAN JBOD write performance (click to enlarge)

Both read and write performance have significantly improved with the new firmware. 100 Mbps JBOD write performance now ranks right after the D-Link DNS-323 and read performance is better than both the DNS-323 and HP Media Vault.

100 Mbps LAN JBOD read performance

Figure 2: 100 Mbps LAN JBOD read performance (click to enlarge)

Performance - 100 Mbps LAN - RAID 1

Figures 3 and 4 show write and read results respectively with a 100 Mbps LAN connection and the N2100 configured in RAID 1 mode. Relative rankings are the same as for JBOD for both write and read, with the N2100 once again showing significantly improved performance.

100 Mbps LAN RAID 1 write performance

Figure 3: 100 Mbps LAN RAID 1 write performance (click to enlarge)

100 Mbps LAN RAID 1 read performance

Figure 4: 100 Mbps LAN RAID 1 read performance (click to enlarge)

More NAS

Wi-Fi System Tools
Check out our Wi-Fi System Charts, Ranker and Finder!

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Over In The Forums

I did the auto update for the firmware and something seemed to have gotten messed up. I used the rescue mode and the firmware recovery tool to get the...
Hi,I have a Merlin 384.5 installed. All working like a charm. Recently I changed some settings in DHCP server menu, added some manually assigned IPs e...
I have a problem with RT-AC1200G+ because it is limiting internet connection bandwidth. I have optic internet connection with 80 Mbps. I was testing w...
I have a RT-AC68U router and need to flush nat conntrack for some reasons.I tried compiled conntrack tool and it does not work.I have noticed that the...
Version 3.0.0.4.384.32799 2018/09/19 42.54 MBytesASUS RT-AC68P Firmware version 3.0.0.4.384.32799Fixed WIFI stability issue.

Don't Miss These

  • 1
  • 2
  • 3