Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Router Charts

Click for Router Charts

Router Ranker

Click for Router Ranker

NAS Charts

Click for NAS Charts

NAS Ranker

Click for NAS Ranker

More Tools

Click for More Tools

Wireless Reviews

VPN

The 2310n supports only two VPN tunnels. But they can be any combination of "dial-in" (client to router) or site-to-site (router to router) connections using PPTP, IPsec or L2TP/IPsec protocols.

Draytek provides its Smart VPN client free for download, which I tried unsuccessfully to use on an XP SP3 notebook to open an IPsec tunnel to the 2130n. This was a few months ago, however, and Draytek has since released a newer version of the utility (4.0.0.1) that I didn't try.

But in the meantime, I took at shot at trying to connect using the VPN Wizard built into Win 7's Network and Sharing Center. I configured the 2130n as shown in Figure 7 and set up a user with only IPsec/L2TP enabled.

VPN IPsec client tunnel setup

Figure 7: VPN IPsec client tunnel setup

On the Win 7 client, I just did the following:

  • Opened the Network and Sharing Center
  • Chose Set up a new connection or network, then Connect to a workplace
  • Chose No, create a new connection, then Use my Internet connection (VPN)
  • Entered the WAN IP of the 2130n
  • Entered the username and password of the test user I set up
  • Clicked the Connect button

Because I disabled the fallback of a PPTP connection, this didn't get me connected. So when the connection failed, I then chose Set up the Connection anyway to save it so that I could make the required changes. After going back to the Network and Sharing Center, I just opened the saved connection and made the settings shown in Figure 8 in the connection Properties. I also clicked the Advanced settings button, to enter the preshared key I'd set in the 2130n.

Win 7 IPsec/L2TP client setup

Figure 8: Win 7 IPsec/L2TP client setup

Once the changes were made, the connection opened within seconds of clicking the Connect button. The 2130n's Remote Dial-in Status screen (Figure 9) showed the successfully opened tunnel.

VPN status
Click to enlarge image

Figure 9: VPN status

I should note that the VPN setup information in the system log was detailed and informative, something not always found in VPN endpoint routers.

I used LAN Speed Test to run a quick check on the 3DES encrypted IPsec tunnel, using a 10 MB file size. Figure 10 shows 1.15 Mbps client to router and 1.3 Mbps router to client.

3DES Ipsec tunnel throughput

Figure 10: 3DES Ipsec tunnel throughput

More Wireless

Wi-Fi System Tools
Check out our Wi-Fi System Charts, Ranker and Finder!

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Over In The Forums

Hi,I have followed this wiki to enable link aggregation/LACP on RT-AC68U and connect it with QNAP TS-453be (by following this instruction).I have star...
I have been using the RT-AC87 for about 5 years now, and it has always been a rock solid router in my opinion. My friend has the opportunity to purcha...
I am having different results using the rootcanary.org test in different browsers. I'll link some photos of my setup and some photos of rootcanary usi...
Hello, I am a novice internet user/gamer and I am experiencing some issues with my upload/download speeds, especially with the upload speeds. I have e...
So I just picked up my new router and installed the Merlin 384.11_2 version as I read once the router updates its wifi with ASUS, it will no longer be...

Don't Miss These

  • 1
  • 2
  • 3