Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Router Charts

Click for Router Charts

Router Ranker

Click for Router Ranker

NAS Charts

Click for NAS Charts

NAS Ranker

Click for NAS Ranker

More Tools

Click for More Tools

Introduction

Actiontec 54Mbps Wireless Network Camera

Actiontec 54Mbps Wireless Network Camera
Summary Manual focus webcam with 11b / g wireless and 10/100 Ethernet connections. Image capture and record features are via Windows-only application
Update None
Pros • Wired and 802.11b/g wireless operation
• Audio and video capture
Cons • Requires ActiveX for web browser viewing
• Windows only software for taking snapshots and video
• No previewing of motion detection settings
• No emailing of snapshots (only video) when motion is detected

In the market for a high quality network camera, but you hate the thought of having to drag ethernet cables everywhere? Actiontec recently introduced its 54 Mbps Wireless Network Camera, which boasts MPEG-4 video and audio recording. While the installation and configuration started off well, I quickly found the product's key limitations.

Mounting hardware
Figure 1: Mounting hardware

The Actiontec wireless camera comes with an AC Adapter, short CAT 5 Ethernet cable, removable antenna, and the mounting hardware pictured above (Figure 1).

Front view

Figure 2: Front view

The front of the camera (Figure 2) has the lens, which is focused by manually turning it. Under the lens is the built-in microphone. On the right side are four LED lights (Ready, Active, LAN, Wireless) that glow amber when the camera is turned on and ready, or active on its Ethernet and wireless connections respectively. Unlike some other cameras (such Axis'), these LEDs cannot be turned off.

Rear view

Figure 3: Rear view

On the back of the camera (Figure 3), going from left to right, we first see the removable wireless antenna. With the correct pigtail adapter to match the RP-TNC connector, you could upgrade to any 2.4GHz antenna you like. To the right of the power connection (5V DC) is an external microphone input, which may give you better results than using the built-in mic.

Since this is a wireless camera, you probably won't use the 10 / 100 LAN port, but it's there for the inital setup of the camera or if you prefer more security than afforded by a wireless connection. Note that the LAN port isn't wired to accept Power over Ethernet, but you could get by this omission using a DIY PoE lash-up or commercially available kit.

Finally the recessed reset button will blast out all the settings and return the camera to the default settings when held for three seconds. But just quickly pressing the button will perform a soft reset including forcing a DHCP release / renew - a nice feature since many reset buttons these days are reset-to-defaults only, which isn't always what the doctor orders.

Wi-Fi System Tools
Check out the new Wi-Fi System Charts, Ranker and Finder!

Featured Sponsors



Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Over In The Forums

Hello Guys,I have a new AC86U and flash it to Merlin 384.5. I use a HDD connect to usb3.0 port and follow a tourist install Transmission (2.94).The pr...
Will the gt-ax 5300 or the gt-ax 11000 or the rt-ax 86u or the rt AX 88u support full cone Nat?As far as I'm aware it can't be enabled in the rt ac88u...
I have an ASUS RT-AC5300 router running the latest stable version of Asuswrt-Merlin (384.5). When I perform an external nmap scan on my IP address, it...
Hi. I just installed Entware on my Asus-Merlin router, and one of the terminal outputs as it installed caught my eye.Code: Configuring locales.Entwar...
Router:RT-AC66U with Merlin's 380.70 firmwareI have just been switched over by my ISP from ADSL to VDSL2. Previously, I connected with PPPoE and easil...

Don't Miss These

  • 1
  • 2
  • 3