Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Router Charts

Click for Router Charts

Router Ranker

Click for Router Ranker

NAS Charts

Click for NAS Charts

NAS Ranker

Click for NAS Ranker

More Tools

Click for More Tools

Introduction

TRENDnet TV-IP572PI

At a Glance
Product TRENDnet TV-IP572PI HD Network camera [Website]
Summary Budget minded HD network camera
Pros • Relatively inexpensive for HD
• 802.3af PoE support
• Motion detection works perfectly
• Basic features work well
Cons • Very short power cord
• May lack features some may deem as important
• Manual focus

TRENDnet recently sent us two of its IP cameras for review. The first we'll be looking at is the TV-IP572PI. I'll be following up in a bit with a shorter comparison review on the TV-IP551WI.

If you take a look at the camera area of TRENDnet's site it can be a little confusing. The TV-IP572 alone has four different models, the TV-IP572P, the TV-IP572PI, the TV-IP572W, and the TV-IP572WI. The decoder ring is: "P" indicates Power over Ethernet (802.3af); "I" indicates a day/night (InfraRed) and "W" indicates wireless.

The TV-IP572PI can be found for about $143 shipped if you do some smart shopping, while the TV-IP551WI can be purchased for $88 shipped. This makes both cameras some of the most economical cameras we have reviewed to date.

Setup

The TV-IP572PI box includes the camera, 5VDC-1.2A wall-wart power adapter with very short power cable, manual, software CD, network cable, and mounting hardware. With the P and PI versions, the short power cable can, of course, be left in the box if you have an 802.3af PoE-capable switch or injector.

TRENDnet's instructions warned not to install or mount the camera until the software installation steps had been followed. I had set up the TV-IP551WI first using the software CD and decided to live dangerously when setting up the TV-IP572PI. I plugged it in to power and network, found it in Overlook Fing, and went to the camera's web interface. I then logged in with the standard admin/admin and was in business. The software installation does strongly suggest changing the admin password, so it may be beneficial for first time users to go through those steps.

Inside

The TV-IP572PI was very easy to take apart, 4 case screws and one board screw. Inside I found 16 MB of Winbond flash and 128 MB of Hynix DDR2 RAM.

Flash and RAM memory of the TRENDnet TV-IP572PI
Figure 1: Flash and RAM memory of the TRENDnet TV-IP572PI

The processor appeared to be a Grain Media variant. However it was hidden under some shielding and not immediately identifiable.

Partially hidden Grain Media processor of the TRENDnet TV-IP572PI
Figure 2: Partially hidden Grain Media processor of the TRENDnet TV-IP572PI

The image sensor is a 1/4" CMOS sensor. The lens has a 4mm focal length with a horizontal field of view of 51.8 degrees. I found out through trial and error that the lens is manual focus, which really wasn't a big deal.

Four IR LEDs are supplied for night vision, which did well compared to other cameras with an equal number of IR LEDs as we'll see later. Rounding out the rest of the internals are a built-in microphone, an audio out jack (no speaker included), and a Micro SD card slot. Figure 3 below shows this detail.

The front panel callouts of the TRENDnet TV-IP572PI
Figure 3: The front panel callouts of the TRENDnet TV-IP572PI
Wi-Fi System Tools
Check out our Wi-Fi System Charts, Ranker and Finder!

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Over In The Forums

So, this is a thing that has bugged me for a long time. When I am on the Network Map page, I see the clients connected with 31 connected clients. Then...
I ran into this issue early today and figure to upgrade the firmware to 384.8_2 since it is available (hoping that fixes the issue)...But I still can ...
Hi..This is related to Asus RT-AC88U firmware version 384.8_2 but I always get "Cannot assign requested address" and "Failed to get IP for interface e...
I have one Asus 68u repeater mode in the basement connected wirelessly to a bell parent modem/router on main floor. Only wifi is working on Asus route...
While waiting for Amazon to deliver the new GT-AX11000, I have opened this thread to discuss this new flagship router.I am going to pair it with my ex...

Don't Miss These

  • 1
  • 2
  • 3