Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Router Charts

Click for Router Charts

Router Ranker

Click for Router Ranker

NAS Charts

Click for NAS Charts

NAS Ranker

Click for NAS Ranker

More Tools

Click for More Tools

Wireless Reviews

Wireless Competitive

For a competitive comparison, I generated a Performance table, selecting the WRT610N V1 and NETGEAR WNDR3700. I also included the dual-band, single radio WRT320N, since it is available as the Cisco Linksys E2000. Figure 7 summarizes the 2.4 GHz band results.

Keep in mind that the WRT610N is the only product in the comparison group to not be tested using the Intel 5300 client. Other reviews have shown that the Intel client has tended to help routers improve their performance in the weaker signal test locations E and F.

Wireless Competitive Comparison - 2.4 GHz

Figure 7: Wireless Competitive Comparison - 2.4 GHz

The chart clearly shows the NETGEAR WNDR3700 as the winner, except running uplink in 20 MHz bandwidth mode, where it's a toss-up among everything except the WRT610N.

Figure 8 compares the same four routers in the 5 GHz band.

Wireless Competitive Comparison - 5 GHz

Figure 8: Wireless Competitive Comparison - 5 GHz

Even though it doesn't always have the highest best case (Location A) throughput, the WNDR3700 tends to have higher throughput than the others in more test locations, especially under medium strength signal conditions.

Use the Wireless Charts to further compare and explore the E3000's performance.

Total Wireless Bandwidth Test

I've noticed that N routers sometimes can produce more aggregate bandwidth using multiple connections than they can over a single connection. So I duplicated the test I ran on the WNDR3700, running multiple simultaneous IxChariot scripts on each radio to see if the E3000 behaved in a similar way.

Figure 9 shows the setup I used for this and the Stress test that follows below. The clients are not correctly identified in the Figure 9 (reused from an old review). The standard Intel 5300 AGN was used as the 2.4 GHz client and a NETGEAR WNDA3100v2 was the 5 GHz client.

Max Bandwidth and Stress Test setup

Figure 9: Max Bandwidth and Stress Test setup

Figure 10 shows a total of 190 Mbps of throughput with four streams running downlink on each radio using 40 MHz channel mode. The WNDR3700, by comparison produced 252 Mbps of aggregate throughput running a similar test. So while the E3000 can squeeze out more bandwidth when more wireless clients are added, the WNDR3700 once again comes out on top.

E3000 simultaneous 2.4 and 5 GHz, 20 MHz channel, downlink
Click to enlarge image

Figure 10: E3000 simultaneous 2.4 and 5 GHz, 20 MHz channel, downlink

More Wireless

Wi-Fi System Tools
Check out our Wi-Fi System Charts, Ranker and Finder!

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Over In The Forums

SO i have two routers the main one I use for my internet which is RT-AC53 and I ordered Another router (RT N12) to extend my wifi/internet 50 Meters a...
I'm setting up a network at another house and would like to have that LAN and my home LAN permanently connected via OpenVPN. Both LANs are AC86U-based...
Hi Guy's,Just got a new AC86U and setup a VPN connection with Newshosting, However on my Xbox1 it now shows that I have a DoubleNAT.Can anyone assist ...
Read the list of 100 worst passwords of 2018.Source: https://www.purevpn.com/blog/worst-password-list/Does any password relate to you in the past? Wha...
Browsing the internet when all the sudden there was a crash. I'm not a very good troubleshooter, but it appears it was the RT-AC88U router (384.9 firm...

Don't Miss These

  • 1
  • 2
  • 3