Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Router Charts

Click for Router Charts

Router Ranker

Click for Router Ranker

NAS Charts

Click for NAS Charts

NAS Ranker

Click for NAS Ranker

More Tools

Click for More Tools

Wireless Reviews

Routing Performance

Routing throughput running the latest 3.13.4 Build 110429 Rel.36959n firmware and our router test process measured 123 Mbps WAN to LAN, 113 Mbps LAN to WAN and 121 Mbps total with up and down tests running simultaneously. The IxChariot composite plot in Figure 5 shows download gets a bit more throughput than upload in the simultaneous routing test.

The maximum simultaneous connections test yielded only 5,109 connections, with the router locking up temporarily after that limit was reached. I didn't have to reboot to get things moving again, but just had to wait a bit for some of the sessions to die off.

Wired routing performance summary

Figure 5: Wired routing performance summary

Wireless Performance

The TL-WR1043ND is Wi-Fi Certified but did not properly default to 20 MHz bandwidth mode on power-up. I successfully ran a Wi-Fi Protected Setup (WPS) session with my Win 7 client by entering the WPS code found on the router's bottom label. The WPS session completed quickly and resulted in a WPA2/AES secured connection. All tests were run with this secured connection using our latest wireless test process.

Because of the problems we found using our standard Intel 5300 test client with only two antennas connected, we've made a change in standard test client. We're now using an Intel Centrino Ultimate-N 6300 in a Lenovo x220i notebook running Win 7 Home Premium. This client will be used for all wireless testing, except when we need to run dual-stream tests on three-stream routers/APs. In that case, we'll use the previous standard Acer Aspire 1810T notebook that also runs Win 7 Home Premium. But it now has a proper dual-stream N client installed, an Intel Centrino Advanced-N 6200.

I filtered the default 2.4 GHz downlink benchmark chart to show only single-band routers. Figure 6 shows that the TL-WR1043ND doesn't do too badly. But its ranking in the uplink benchmarks is much lower, falling to the lower half of the rankings.

Average 2.4 GHz Downlink Throughput

Figure 6: Average 2.4 GHz Downlink Throughput

For a comparative look, I chose two other inexpensive single-band routers with Gigabit ports, the EnGenius ESR9850 and Buffalo WZR-HP-G300NH. Figure 7 shows only occasional wins for the TP-LINK, both for downlink and both in mid-level signal test locations.

Wireless Performance Comparison

Figure 7: Wireless Performance Comparison

You can see overall poor uplink performance and also that throughput is very low in the weakest signal test location F. Highest throughput of 85 Mbps was measured in Location A, in 40 MHz mode running downlink. I was able to measure 98 Mbps of total throughput in a Location A simultaneous up/down test using 40 MHz bandwidth mode.

The bottom line is that this is not a router that is going to provide exceptional uplink performance, nor will it be especially helpful for extending your wireless range.

The IxChariot plot in Figure 8 shows relatively stable throughput, which was generally the case.

 xChariot plot - 2.4 GHz, 20 MHz, downlink

Figure 8: IxChariot plot - 2.4 GHz, 20 MHz, downlink

Here are links to the other 2.4 GHz plots for your reference:

Closing Thoughts

For a top-of-line router, the TL-WR1043ND's performance isn't particularly impressive. But for a $55 single-band N router with Gigabit ports, it isn't too bad. Be sure to hit Craig's full feature review and use the Router Charts and all the benchmarks therein and the Router Finder to further explore its performance and features.

More Wireless

Wi-Fi System Tools
Check out our Wi-Fi System Charts, Ranker and Finder!

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Over In The Forums

Is there a way to disable the pop-up when hovering the mouse pointer over threads?
Recently got a RT-AC86u and installed with the latest Merlin (384.18), and noticed WebUI being unresponsive after a while. Restarting the httpd servic...
I've installed last version of Asus Merlin. I have tried to install pyload but now the default version of python in entware is version 3. Pyload still...
Asuswrt-Merlin 384.19 beta is now available (except for the RT-AX56U which won't be available for this release, due to outdated GPL code).The main cha...
Hi There,Update 2020/07/28Here we have new 386 rc2 beta for public test(so the old links are removed).link: https://drive.google.com/drive/folders/1wv...

Don't Miss These

  • 1
  • 2
  • 3